www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 high efficiency heterojunction power fet chip (.25 m x 2 00 m) the berex bcp0 2 0 t is a gaas power phemt with a nominal 0. 2 5 micron gate length and 2 00 micron gate width making the product ideally suited for applications where high - gain and medium power in the 1000 mhz to 26.5 ghz frequency range are required. the product may be used in either wideband (6 - 18 ghz) or narrow - band applications. the bcp0 2 0 t is produced using state of the art metallization with si 3 n 4 passivation and is screened to assure reliability. product features ? 2 4 dbm typical output power ? 1 4 db typical gain @ 12 ghz ? 0. 2 5 x 2 00 micron recessed gate applications ? commercial ? military / hi - rel . ? test & measurement electrical characteristic ( tuned for power ) t a = 25 c symbol parameter/test conditions test freq . min. typical m ax . unit p 1db output power @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 22.5 24.0 24.0 dbm g 1db gain @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 1 2 . 0 14.0 12.0 db pae pae @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 60 55 % nf 50 ohm noise figure (v ds =2v, i ds =10 ma 12 ghz 1.09 db i dss saturated drain current (v gs = 0v, v ds = 3 v) 4 0 60 80 ma g m transconductance (v ds = 3v, v gs = 50% i dss ) 80.0 ms v p pinch - off voltage (i ds = 0. 3 m a, v ds = 3 v) - 2.5 - 1.1 - 0.5 v bv gd drain breakdown voltage (i g = 0. 6 ma, source open) - 1 5 - 1 2 v bv gs source breakdown voltage (i g = 0. 6 ma, drain open) - 1 3 v r th thermal resistance (au - sn eutectic attach) 160 c/w BCP020T
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP020T electrical characteristic ( tuned for gain ) t a = 25 c symbol parameter/test conditions test freq . min . typical max . unit p 1db output power @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 20.0 21.0 21.0 dbm g 1db gain @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 15.5 17.0 13.0 db pae pae @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 45 45 % nf 50 ohm noise figure (v ds =2v, i ds =10 ma 12 ghz 1.09 db i dss saturated drain current (v gs = 0v, v ds = 1.0v) 4 0 60 80 ma g m transconductance (v ds = 3v, v gs = 50% i dss ) 80.0 ms v p pinch - off voltage (i ds = 0. 3 m a, v ds = 3 v) - 2.5 - 1.1 - 0.5 v bv gd drain breakdown voltage (i g = 0. 6 ma, source open) - 1 5 - 1 2 v bv gs source breakdown voltage (i g = 0. 6 ma, drain open) - 1 3 v r th thermal resistance (au - sn eutectic attach) 160 c/w maximum rating (t a = 25 c) symbols parameters absolute continuous v ds v gs i ds i gsf p in t ch t stg p t drain - source voltage gate - source voltage drain current forward gate current input power channel temperature storage temperature total power dissipation 12 v - 6 v i dss 1 1 ma 17 dbm 175 c - 60 c - 150 c 1 . 0 w 8 v - 3 v i dss 2 ma @ 3db compression 150 c - 60 c - 150 c 0.8 w exceeding any of the above maximum ratings will result in reduced mttf and may cause permanent damage to the device.
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP020T p in _p out /gain, pae (12 ghz) frequency = 12ghz v ds = 8 v, i ds = 50% i dss (tuned for power) frequency = 12ghz v ds = 8 v, i ds = 50% i dss (tune d for gain) p in _p out /gain, pae (18 ghz) frequency = 18ghz v ds = 8 v, i ds = 50% i dss (tuned for power) frequency = 18ghz v ds = 8 v, i ds = 50% i dss (tune d for gain )
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP020T s - parameter ( v ds = 8v, i ds = 50% i dss ) freq . [ g hz] s11 [ mag ] s11 [ang . ] s21 [ mag ] s21 [ang . ] s12 [ mag ] s12 [ang . ] s22 [ mag ] s22 [ang . ] 1 0.98 - 17.63 6.54 165.56 0.014 81.13 0.80 - 5.99 2 0.95 - 35.11 6.35 152.34 0.027 70.37 0.78 - 11.31 3 0.90 - 52.87 6.08 140.12 0.039 64.06 0.75 - 15.78 4 0.85 - 69.99 5.77 127.94 0.048 53.79 0.71 - 20.09 5 0.80 - 88.24 5.43 116.00 0.054 47.49 0.67 - 24.42 6 0.76 - 105.52 5.04 104.87 0.058 40.26 0.63 - 27.88 7 0.72 - 122.72 4.68 93.83 0.063 33.49 0.59 - 32.54 8 0.71 - 138.65 4.33 84.53 0.064 29.01 0.56 - 34.82 9 0.69 - 152.44 3.97 75.99 0.063 25.78 0.53 - 36.61 10 0.68 - 166.12 3.69 67.53 0.064 22.40 0.51 - 38.64 11 0.69 - 178.47 3.38 59.72 0.064 18.97 0.47 - 39.57 12 0.70 170.61 3.17 51.75 0.067 17.78 0.46 - 42.35 13 0.71 158.55 2.94 44.52 0.061 12.25 0.43 - 43.48 14 0.73 149.14 2.73 37.18 0.062 12.90 0.40 - 45.06 15 0.74 140.53 2.57 30.17 0.063 10.83 0.37 - 47.57 16 0.78 131.12 2.40 22.71 0.064 8.80 0.33 - 49.99 17 0.81 125.12 2.23 15.52 0.062 6.82 0.29 - 55.76 18 0.82 117.90 2.06 8.53 0.066 2.23 0.24 - 62.01 19 0.84 111.86 1.89 0.82 0.065 0.95 0.19 - 72.70 20 0.86 109.58 1.74 - 5.04 0.066 - 1.33 0.14 - 89.32 21 0.87 105.71 1.60 - 11.40 0.068 - 0.98 0.11 - 123.58 22 0.88 103.28 1.45 - 17.65 0.068 - 3.31 0.13 - 160.51 23 0.88 103.13 1.32 - 22.86 0.070 - 5.10 0.18 174.94 24 0.88 101.01 1.20 - 28.51 0.070 - 5.63 0.25 162.82 25 0.90 100.91 1.08 - 33.17 0.066 - 6.26 0.32 154.30 26 0.90 102.38 1.00 - 36.21 0.070 - 2.08 0.38 150.28 note: s - parameters include bond wires. reference planes are at edge of substrates shown on wire bonding information figure below.
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP020T wire bonding information using 1 mil . diameter, au bonding wires. 1. gate to input transmission line - length and height : 600 m x 250 m - number of wire (s) : 1 2. drain to output transmission line - length and height : 400 m x 250 m - number of wire(s) : 1 3. source to ground plate - length and height : 250 m x 300 m - number of wire(s) : 4 disclaimer berex reserves the right to make changes without further notice to any products herein to improve reliability, function or design. berex does not assume any liability arising out of the application or use of any product or circuit described herein. life support policy berex products are not authorized for use as critical components in life support devices without the express written approval of berex. 1. life support devices or systems are devices or systems which (a) are intended for surgical implant into the body, or (b) support or sustain li fe, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labeling, can be reasonably expected to result in significant injury to the user. 2. a critical component is any component of a life support device or s ystem whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
|
